THE ULTIMATE
1/2/2019 0 Comments Quintum Tenor Cli Guide PdfPDF Epub audio books. Download now. ![]() • Open Internet Explorer and click Tools and then Internet Options. • Click the Advanced tab. • Click Reset. • When done, try again • it might be due to spyware or virus attack • you could disable firewall • • Open Internet Explorer and click Tools, Internet Options, and then click the Security tab. • Select Trusted Sites, and then click the Default Level button. • Click the Advanced tab and scroll to the Security Options section. • Select Use SSL 2.0 and Use SSL 3.0 if they are not already selected. • Click the Content tab. • Click the Clear SSL State button, and then click OK. You should now be able to view secure Web sites if you had to make any selection. Browse to a secure Web page to make sure. If you still cannot access the page, use the remaining steps to resolve the problem. • If you are using IE 7, temporarily disable the built-in phishing filter, using the following steps: • Open IE 7. • Click Tools, select Phishing Filter, and then select Turn Off Automatic Website Checking. • Go to the Website and try again. CAUTION: With the phishing filter off you must know and trust the website that you are trying to view. Do not not enter any personal information into a Web form unless you can verify the site is reputable. • After you have visited the site, re-enable the phishing filter. • In Windows XP, use the following steps to register the device libraries associated with Internet security: • Click Start, Run. • Enter cmd into the open field. • Enter each of the following items in the command window, clicking OK after each name has been entered: • regsvr32 softpub.dll • regsvr32 wintrust.dll• regsvr32 initpki.dll • regsvr32 dssenh.dll• regsvr32 rsaenh.dll• regsvr32 gpkcsp.dll• regsvr32 sccbase.dll• regsvr32 slbcsp.dll• regsvr32 cryptdlg.dll • Type Exit and then press the Enter key. • Click OK, and then restart the computer. Incase the issue gets unresolved get in touch with me at [email protected]| 86 views| 0 helpful votes. Hi a_rappaport, If you want to restore the factory defaults, please follow the steps below. Note: All current configuration will be deleted, including your password. Restoring factory defaults does not change or delete the Tenor's IP address, subnet mask or default gateway; you will still be able to communicate with the unit after a reset. You can set all system configuration settings back to their factory defaults through the Command Line Interface (CLI) as follows: 1. Access the CLI through a Telnet session. See the Command Line Interface (CLI) guide for more information. What does the red dot on wd my passport for mac mean. • Green: Indicates that the battery is between 50-89% power. • Red: Indicates that the battery is between 8-19% power. • Orange: Indicates that the battery is between 20-49% power. • Blinking White: Boot-up or USB mode activity. Also indicates SD card transfer activity. Access the Config-VOIPNetwork-1 prompt. Type setfactory. You will be asked if you are sure you want to set the unit back to factory defaults. Type yes to confirm (type no to cancel the restore). Reset System The Reset system feature enables you to reset the system, including hardware and software. You can reset the system through the unit's Back Panel or through the Command Line Interface (CLI). Use a blunt, thin object to press in the Reset button, located on Tenor AX's front panel. The system will reset. Command Line Interface (CLI). You can reset the system through the Command Line Interface (CLI) as follows: 1. Access the CLI through a Telnet session. See the Command Line Interface (CLI) guide for more information. Access the Maintain-MasterChassis-1# prompt. You will be asked if you are sure you want to set the unit back to factory defaults. Type yes to confirm (type no to cancel the restore). Through this simple Command Line Interface (CLI) telnet session, you can access all configuration options, including an online help system, built into the CLI, which provides help for all features and functions. Just type help at any prompt, and data about that field will be displayed. Hope it helps. Thank you for using FixYa.| 652 views| 0 helpful votes. Tenor AXG VoIP Gateway (AXG800, AXG1600, AXG2400) Configuration The Tenor AXG VoIP Gateway Configuration is used for (Phone/FXS) to VoIP connections; calls coming from the Phone/FXS interface (i.e.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |